International Journal of Science, Technology and Society

| Peer-Reviewed |

A Leakage Current Forecast of the Polymeric Insulator Using ANFIS Method Based on LabView Pre-processed Thermal Image

Received: Oct. 28, 2018    Accepted: Dec. 04, 2018    Published: Jan. 04, 2019
Views:       Downloads:

Share This Article

Abstract

This paper reports estimates of leaky currents based on Thermal (Infrared) images of polymer insulators using LabVIEW as preliminary data from the ANFIS method for the purpose of condition-based non-contact monitoring. In this study, images of very high contaminated polymer insulators were taken using the FLIR-A600 thermal camera series. The laboratory pollution performance test is carried out in accordance with the standards of IEC 60507 with an 18 kV AC voltage. The pollution severity is indicated because the ESDD value is very high contaminated and the relative humidity conditions are maintained at the range of 85% RH to 95% RH and temperature at 28°C. Humidity and temperature are maintained through a mist-producing container that is connected to a controlled polymer isolator test container using an Arduino microcontroller with temperature and humidity sensors. LabVIEW is used to calculate the percentage of RGB color from a thermal image related to a certain measured leakage current. This RGB data is training data for ANFIS to predict leaky currents. The results show that this method is able to predict current leakage without spending time to reach RMSE 0.00008. By adding a calculation to determine the condition of the insulator in the category of Safe, Maintenance or Hazard so that the Field Technician can decide whether the insulator must be replaced or not. With a non-contact method that only through thermal analysis of polymer insulators can accelerate the process of checking the condition of the insulator.

DOI 10.11648/j.ijsts.20180606.11
Published in International Journal of Science, Technology and Society ( Volume 6, Issue 6, November 2018 )
Page(s) 88-95
Creative Commons

This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.

Copyright

Copyright © The Author(s), 2024. Published by Science Publishing Group

Keywords

Polymeric Insulator, Leakage Current, Partial Discharge, Infrared Images, Pollution

References
[1] G. E. Asimakopoulou, V. T. Kontargyri, G. J. Tsekouras, C. N. Elias, F. E. Asimakopoulou, and I. a. Stathopulos, “A fuzzy logic optimization methodology for the estimation of the critical flashover voltage on insulators,” Electr. Power Syst. Res., vol. 81, no. 2, pp. 580–588, 2011.
[2] M. I. Mousa, Z. Abdul-Malek, and Z. I. Mousa, “Aging Detection of Glass Disc Insulator by Using Infrared Camera,” Indones. J. Electr. Eng. Comput. Sci., vol. 6, no. 3, p. 520, 2017.
[3] L. Jin and D. Zhang, “Contamination Grades Recognition of Ceramic Insulators Using Fused Features of Infrared and Ultraviolet Images,” Energies, vol. 8, no. 2, pp. 837–858, 2015.
[4] D. Pylarinos, “Discharges Classification using Genetic Algorithms and Feature Selection Algorithms on Time and Frequency Domain Data Extracted from Leakage Current Measurements,” vol. 3, no. 6, pp. 544–548, 2013.
[5] R. Boudissa, S. Djafri, A. Haddad, R. Belaicha, and R. Bearsch, “Effect of insulator shape on surface discharges and flashover under polluted conditions,” IEEE Trans. Dielectr. Electr. Insul., vol. 12, no. 3, pp. 429–437, 2005.
[6] H. Yang et al., “Effect of profiles on ac contamination flashover performance of large-tonnage suspension disc insulators,” IEEE Trans. Dielectr. Electr. Insul., vol. 21, no. 6, pp. 2476–2485, 2014.
[7] P. C. Miao and Z. N. Xu, “Effects of different sample resistances on the insulator leakage current acquisition results,” Appl. Mech. Mater., vol. 644–650, pp. 3468–3471, 2014.
[8] B. Banhthasit, K. Tonmitra, A. Kaewrawang, and A. Suksri, “Evaluating on Effect of HVAC Series with Impulse Excitation Voltage on Porcelain Insulator by Using Rotating Wheel Dip Test,” Adv. Mater. Res., vol. 354–355, pp. 159–164, 2011.
[9] J. Jiang, R. Mu, C. Li, and Y. Luo, “High Sensitive FBG Sensor for Equivalent Salt,” vol. 27, no. 2, pp. 177–180, 2015.
[10] N. a. Al-Geelani, M. A. M. Piah, Z. Adzis, and M. a. Algeelani, “Hybrid regrouping PSO based wavelet neural networks for characterization of acoustic signals due to surface discharges on H.V. glass insulators,” Appl. Soft Comput. J., vol. 13, no. 12, pp. 4622–4632, 2013.
[11] Suwarno and A. B. Wibowo, “Increasing the performances of various types outdoor insulators by using RTV silicone rubber coating,” Int. J. Electr. Eng. Informatics, vol. 4, no. 4, pp. 608–619, 2012.
[12] S. Chandrasekar, C. Kalaivanan, A. Cavallini, and G. Montanari, “Investigations on leakage current and phase angle characteristics of porcelain and polymeric insulator under contaminated conditions,” IEEE Trans. Dielectr. Electr. Insul., vol. 16, no. 2, pp. 574–583, 2009.
[13] D. Pylarinos, K. Siderakis, and E. Pyrgioti, “Measuring and Analyzing Leakage Current for,” vol. 29, pp. 31–53, 2011.
[14] M. H. Samimi, A. H. Mostajabi, I. Ahmadi-Joneidi, A. A. Shayegani-Akmal, and H. Mohseni, “Performance Evaluation of Insulators Using Flashover Voltage and Leakage Current,” Electr. Power Components Syst., vol. 41, no. 2, pp. 221–233, 2013.
[15] F. Pratomosiwi and Suwarno, “Performance improvement of the ceramic outdoor insulators located at highly polluted environment using room temperature vulcanized silicone rubber coating,” Int. J. Electr. Eng. Informatics, vol. 2, no. 1, pp. 15–28, 2010.
[16] V. J. Narayanan, M. Sivakumar, K. Karpagavani, and S. Chandrasekar, “Prediction of Flashover and Pollution Severity of High Voltage Transmission Line Insulators Using Wavelet Transform and Fuzzy C-Means Approach,” vol. 9, 2014.
[17] Z. Sahli, a. Mekhaldi, R. Boudissa, and S. Boudrahem, “Prediction parameters of dimensioning of insulators under non-uniform contaminated conditions by multiple regression analysis,” Electr. Power Syst. Res., vol. 81, no. 4, pp. 821–829, 2011.
[18] Darwison, S. Arief, H. Abral, A. Hazmi, Aulia and M. H. Ahmad, “Thermal Image, Partial Discharge And Leakage Current Correlation Of Ceramic Insulator Under Different Contamination Level,” vol. 12, no. 18, pp. 5235–5240, 2017.
[19] J. Li, W. Sima, C. Sun, and S. a. Sebo, “Use of leakage currents of insulators to determine the stage characteristics of the flashover process and contamination level prediction,” IEEE Trans. Dielectr. Electr. Insul., vol. 17, no. 2, pp. 490–501, 2010.
[20] I. Ahmadi-Joneidi, A. Majzoobi, A. Shayegani-Akmal, H. Mohseni, and J. Jadidian, “Aging evaluation of silicone rubber insulators using leakage current and flashover voltage analysis,” IEEE Trans. Dielectr. Electr. Insul., vol. 20, no. 1, pp. 212–220, 2013.
[21] X. Guoxiang and P. B. McGrath, “Electrical and thermal analysis of polymer insulator under contaminated surface conditions,” Dielectr. Electr. Insul. IEEE Trans., vol. 3, no. 2, pp. 289–298, 1996.
[22] E. P. Waldi et al., “Automatic threshold of standard deviation to reject noise in raw data of partial discharges,” ARPN J. Eng. Appl. Sci., vol. 12, no. 18, pp. 5319–5324, 2017.
Cite This Article
  • APA Style

    Darwison Darwison, Syukri Arief, Hairul Abral, Ariadi Hazmi, Novizon Novizon, et al. (2019). A Leakage Current Forecast of the Polymeric Insulator Using ANFIS Method Based on LabView Pre-processed Thermal Image. International Journal of Science, Technology and Society, 6(6), 88-95. https://doi.org/10.11648/j.ijsts.20180606.11

    Copy | Download

    ACS Style

    Darwison Darwison; Syukri Arief; Hairul Abral; Ariadi Hazmi; Novizon Novizon, et al. A Leakage Current Forecast of the Polymeric Insulator Using ANFIS Method Based on LabView Pre-processed Thermal Image. Int. J. Sci. Technol. Soc. 2019, 6(6), 88-95. doi: 10.11648/j.ijsts.20180606.11

    Copy | Download

    AMA Style

    Darwison Darwison, Syukri Arief, Hairul Abral, Ariadi Hazmi, Novizon Novizon, et al. A Leakage Current Forecast of the Polymeric Insulator Using ANFIS Method Based on LabView Pre-processed Thermal Image. Int J Sci Technol Soc. 2019;6(6):88-95. doi: 10.11648/j.ijsts.20180606.11

    Copy | Download

  • @article{10.11648/j.ijsts.20180606.11,
      author = {Darwison Darwison and Syukri Arief and Hairul Abral and Ariadi Hazmi and Novizon Novizon and Aulia Aulia and Eka Putra Waldi},
      title = {A Leakage Current Forecast of the Polymeric Insulator Using ANFIS Method Based on LabView Pre-processed Thermal Image},
      journal = {International Journal of Science, Technology and Society},
      volume = {6},
      number = {6},
      pages = {88-95},
      doi = {10.11648/j.ijsts.20180606.11},
      url = {https://doi.org/10.11648/j.ijsts.20180606.11},
      eprint = {https://download.sciencepg.com/pdf/10.11648.j.ijsts.20180606.11},
      abstract = {This paper reports estimates of leaky currents based on Thermal (Infrared) images of polymer insulators using LabVIEW as preliminary data from the ANFIS method for the purpose of condition-based non-contact monitoring. In this study, images of very high contaminated polymer insulators were taken using the FLIR-A600 thermal camera series. The laboratory pollution performance test is carried out in accordance with the standards of IEC 60507 with an 18 kV AC voltage. The pollution severity is indicated because the ESDD value is very high contaminated and the relative humidity conditions are maintained at the range of 85% RH to 95% RH and temperature at 28°C. Humidity and temperature are maintained through a mist-producing container that is connected to a controlled polymer isolator test container using an Arduino microcontroller with temperature and humidity sensors. LabVIEW is used to calculate the percentage of RGB color from a thermal image related to a certain measured leakage current. This RGB data is training data for ANFIS to predict leaky currents. The results show that this method is able to predict current leakage without spending time to reach RMSE 0.00008. By adding a calculation to determine the condition of the insulator in the category of Safe, Maintenance or Hazard so that the Field Technician can decide whether the insulator must be replaced or not. With a non-contact method that only through thermal analysis of polymer insulators can accelerate the process of checking the condition of the insulator.},
     year = {2019}
    }
    

    Copy | Download

  • TY  - JOUR
    T1  - A Leakage Current Forecast of the Polymeric Insulator Using ANFIS Method Based on LabView Pre-processed Thermal Image
    AU  - Darwison Darwison
    AU  - Syukri Arief
    AU  - Hairul Abral
    AU  - Ariadi Hazmi
    AU  - Novizon Novizon
    AU  - Aulia Aulia
    AU  - Eka Putra Waldi
    Y1  - 2019/01/04
    PY  - 2019
    N1  - https://doi.org/10.11648/j.ijsts.20180606.11
    DO  - 10.11648/j.ijsts.20180606.11
    T2  - International Journal of Science, Technology and Society
    JF  - International Journal of Science, Technology and Society
    JO  - International Journal of Science, Technology and Society
    SP  - 88
    EP  - 95
    PB  - Science Publishing Group
    SN  - 2330-7420
    UR  - https://doi.org/10.11648/j.ijsts.20180606.11
    AB  - This paper reports estimates of leaky currents based on Thermal (Infrared) images of polymer insulators using LabVIEW as preliminary data from the ANFIS method for the purpose of condition-based non-contact monitoring. In this study, images of very high contaminated polymer insulators were taken using the FLIR-A600 thermal camera series. The laboratory pollution performance test is carried out in accordance with the standards of IEC 60507 with an 18 kV AC voltage. The pollution severity is indicated because the ESDD value is very high contaminated and the relative humidity conditions are maintained at the range of 85% RH to 95% RH and temperature at 28°C. Humidity and temperature are maintained through a mist-producing container that is connected to a controlled polymer isolator test container using an Arduino microcontroller with temperature and humidity sensors. LabVIEW is used to calculate the percentage of RGB color from a thermal image related to a certain measured leakage current. This RGB data is training data for ANFIS to predict leaky currents. The results show that this method is able to predict current leakage without spending time to reach RMSE 0.00008. By adding a calculation to determine the condition of the insulator in the category of Safe, Maintenance or Hazard so that the Field Technician can decide whether the insulator must be replaced or not. With a non-contact method that only through thermal analysis of polymer insulators can accelerate the process of checking the condition of the insulator.
    VL  - 6
    IS  - 6
    ER  - 

    Copy | Download

Author Information
  • Department of Electrical Engineering, Universitas Andalas, Padang, Indonesia; Department of Chemistry, Universitas Andalas, Padang, Indonesia

  • Department of Chemistry, Universitas Andalas, Padang, Indonesia

  • Department of Mechanical Engineering, Universitas Andalas, Padang, Indonesia

  • Department of Electrical Engineering, Universitas Andalas, Padang, Indonesia

  • Department of Electrical Engineering, Universitas Andalas, Padang, Indonesia

  • Department of Electrical Engineering, Universitas Andalas, Padang, Indonesia

  • Department of Electrical Engineering, Universitas Andalas, Padang, Indonesia

  • Section