Simulation Study on Blast Resistance Test of Blast Wall Based on LS-DYNA Coupling Method

Zhu Gan; Ding Jianguo

doi:doi:10.11648/j.sd.20210903.16

| Peer-Reviewed

Simulation Study on Blast Resistance Test of Blast Wall Based on LS-DYNA Coupling Method

Zhu Gan, Ding Jianguo

Published in Science Discovery (Volume 9, Issue 3)

Received: 14 April 2021 Published: 24 May 2021

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

In order to study the pressure change with time at the blast face of the blast resistant wall when the shock wave acts on the blast resistant wall after the explosion of TNT explosive, the equivalent model of the blast resistant wall is designed based on the similarity theory, and the TNT near ground explosion test is carried out. During the test, the pressure change data of the design measuring point on the blast resistant wall with time are collected by high-speed data acquisition instrument and pressure sensor, The time history curve of shock wave overpressure was obtained by processing the data. Then, LS-DYNA finite element analysis software is used to establish a separate finite element model of the blast wall. At the same time, the relevant parameters of air, explosive, concrete and ground in the explosion field are set. The numerical simulation of the explosion field is carried out, and the overpressure time history curve at the measuring point is extracted by the finite element analysis post-processing software. Compared with the numerical simulation results, it is found that the numerical simulation results are in good agreement with the experimental data, which indicates that the selection and setting of parameters in the simulation calculation are reasonable. The model and algorithm provide an effective means for the numerical simulation of blast wall in the explosion field.

Published in	Science Discovery (Volume 9, Issue 3)
DOI	10.11648/j.sd.20210903.16
Page(s)	114-120
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2021. Published by Science Publishing Group

Keywords

TNT, Explosion Shock Wave, Blast Wall, LS-DYNA

References

[1]	J.Henrych著,熊建国等译.爆炸动力学及其应用[M].北京:科学出版社,1979.
[2]	张守中,孙业斌.爆炸载荷作用下刚塑性圆柱壳体的变形和破裂[J].兵工学报,1985(02):59-65.
[3]	Zhang Shouzhong,Sun Yebin. Deformation and rupture of rigid-plastic cylinder shell due to explosion[J]. Acta Armamentarii,1985(02):59-65.
[4]	Wu Chengqing，Hao Hong．Modeling of simultaneous ground shock and airblast pressure on nearby structures from surface explosions[J].International Journal of Impact Engineering，2005,31(6):699-717.
[5]	仲倩,王伯良,黄菊,等.TNT空中爆炸超压的相似律[J].火炸药学报,2008,33(4):32-35.
[6]	ZHONG Qian,WANG Bo-liang.HU ANG Ju, HUI Jun-ming. Study on the Similarity Law of TNT Explosion Overpressure in Air[J]. Chinese Journal of Explosives & Propellants, 2008,33(4):32-35.
[7]	梁利平,李鑫.挡墙对爆炸冲击波传播影响的三维数值模拟[J].福建师范大学福清分校学报,2011(05):26-30.
[8]	LIANG Liping,LI Xin. Three- dimensional Numerical Value Simulation of Retailing Wall to the Blast Wave Propagating Influence[J].Journal of Fuqing branch of Fujian normal university, 2011(05):26-30.
[9]	刘伟,郑毅,秦飞.近地面TNT爆炸的试验研究和数值模拟[J].爆破,2012(03):1-9.
[10]	LIU Wei,ZHENG Yi,QIN Fei. Experimental and Numerical Simulation of TNT Explosion on the Ground[J]. BLASTING,2012(03):1-9.
[11]	白金泽.LS-DYNA3D理论基础与实例分析[M].北京:科学出版社,2005.
[12]	BAI jinze. Theoretical basis and case analysis of LS-DYNA3D[M].beijing: Science Press,2005.
[13]	史春芳,徐赵东.工程结构抗爆技术的研究现状[J].西安建筑科技大学学报(自然科学版),2007(05):616-620.
[14]	SHI Chun-fang,XU Zhao-dong.Anti-explosion technology in engineering structure[J]. Xi'an Univ.of Arch.&Tech.(Natural Science Edition),2007(05):616-620.
[15]	杨俊杰.相似理论与结构模型试验[M].武汉:武汉理工大学出版社.2005.
[16]	LS-DYNA Keyword User’s Manual(LS-DYNA用户手册)[M].2017.
[17]	Alia A,Souli M,High explosive simulation using multi-material formulations[J]. Applied Thermal Engineering,2006,26(10):1032-1042.
[18]	李楠.钢纤维高强混凝土墙的抗爆性能有限元分析[D].长安大学,2012.
[19]	Li Nan.Finite Element Anslysis of Steel Fiber Reinforced High Strength Concrete Walls Subjected to Blasting Load.[D].Chang’an University,2012.
[20]	穆朝民,任辉启,李永池,等.爆炸冲击波作用于墙体及对墙体绕射的实验研究[J].实验力学, 2008,23(02): 169-174.
[21]	M U Chao-min, REN Hui-qi, LI Yong-chi, XIN Kai. Experimental Study of Blast Wave Reflection and Diffraction on a Shelter Wall[J]. Journal of Experimental Mechanics, 2008,23(02): 169-174.
[22]	张千里,张耀,年鑫哲.混凝土防爆墙对爆炸冲击波传播的影响[J].振动与冲击, 2013(24): 192-197.
[23]	ZHANG Qian-li,ZHANG Yao,NIAN Xin-zhei. Effect of concrete protective wall on explosion shock wave[J]. Journal of Vibration and Shock,2013(24): 192-197.
[24]	陈鑫,高轩能.炸药近地爆炸的数值模拟及影响参数的分析[J].华侨大学学报(自然科学版),2014,35(05):570-575.
[25]	Chen Xin, Gao Xuanneng,Numerical Simulation and Analysis of Influence Paramenters for Explosions Near Ground[J].Journal of Huaqiao University(Natural Science),2014,35(05):570-575.

Cite This Article

Plain Text BibTeX RIS

APA Style

Zhu Gan, Ding Jianguo. (2021). Simulation Study on Blast Resistance Test of Blast Wall Based on LS-DYNA Coupling Method. Science Discovery, 9(3), 114-120. https://doi.org/10.11648/j.sd.20210903.16

Copy | Download

ACS Style

Zhu Gan; Ding Jianguo. Simulation Study on Blast Resistance Test of Blast Wall Based on LS-DYNA Coupling Method. Sci. Discov. 2021, 9(3), 114-120. doi: 10.11648/j.sd.20210903.16

Copy | Download

AMA Style

Zhu Gan, Ding Jianguo. Simulation Study on Blast Resistance Test of Blast Wall Based on LS-DYNA Coupling Method. Sci Discov. 2021;9(3):114-120. doi: 10.11648/j.sd.20210903.16

Copy | Download

@article{10.11648/j.sd.20210903.16,
  author = {Zhu Gan and Ding Jianguo},
  title = {Simulation Study on Blast Resistance Test of Blast Wall Based on LS-DYNA Coupling Method},
  journal = {Science Discovery},
  volume = {9},
  number = {3},
  pages = {114-120},
  doi = {10.11648/j.sd.20210903.16},
  url = {https://doi.org/10.11648/j.sd.20210903.16},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.sd.20210903.16},
  abstract = {In order to study the pressure change with time at the blast face of the blast resistant wall when the shock wave acts on the blast resistant wall after the explosion of TNT explosive, the equivalent model of the blast resistant wall is designed based on the similarity theory, and the TNT near ground explosion test is carried out. During the test, the pressure change data of the design measuring point on the blast resistant wall with time are collected by high-speed data acquisition instrument and pressure sensor, The time history curve of shock wave overpressure was obtained by processing the data. Then, LS-DYNA finite element analysis software is used to establish a separate finite element model of the blast wall. At the same time, the relevant parameters of air, explosive, concrete and ground in the explosion field are set. The numerical simulation of the explosion field is carried out, and the overpressure time history curve at the measuring point is extracted by the finite element analysis post-processing software. Compared with the numerical simulation results, it is found that the numerical simulation results are in good agreement with the experimental data, which indicates that the selection and setting of parameters in the simulation calculation are reasonable. The model and algorithm provide an effective means for the numerical simulation of blast wall in the explosion field.},
 year = {2021}
}

Copy | Download

TY  - JOUR
T1  - Simulation Study on Blast Resistance Test of Blast Wall Based on LS-DYNA Coupling Method
AU  - Zhu Gan
AU  - Ding Jianguo
Y1  - 2021/05/24
PY  - 2021
N1  - https://doi.org/10.11648/j.sd.20210903.16
DO  - 10.11648/j.sd.20210903.16
T2  - Science Discovery
JF  - Science Discovery
JO  - Science Discovery
SP  - 114
EP  - 120
PB  - Science Publishing Group
SN  - 2331-0650
UR  - https://doi.org/10.11648/j.sd.20210903.16
AB  - In order to study the pressure change with time at the blast face of the blast resistant wall when the shock wave acts on the blast resistant wall after the explosion of TNT explosive, the equivalent model of the blast resistant wall is designed based on the similarity theory, and the TNT near ground explosion test is carried out. During the test, the pressure change data of the design measuring point on the blast resistant wall with time are collected by high-speed data acquisition instrument and pressure sensor, The time history curve of shock wave overpressure was obtained by processing the data. Then, LS-DYNA finite element analysis software is used to establish a separate finite element model of the blast wall. At the same time, the relevant parameters of air, explosive, concrete and ground in the explosion field are set. The numerical simulation of the explosion field is carried out, and the overpressure time history curve at the measuring point is extracted by the finite element analysis post-processing software. Compared with the numerical simulation results, it is found that the numerical simulation results are in good agreement with the experimental data, which indicates that the selection and setting of parameters in the simulation calculation are reasonable. The model and algorithm provide an effective means for the numerical simulation of blast wall in the explosion field.
VL  - 9
IS  - 3
ER  -

Copy | Download

Author Information

Zhu Gan

College of Science, Nanjing University of Scinece and Technology, Nanjing, China
Ding Jianguo

College of Science, Nanjing University of Scinece and Technology, Nanjing, China

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Zhu Gan, Ding Jianguo. (2021). Simulation Study on Blast Resistance Test of Blast Wall Based on LS-DYNA Coupling Method. Science Discovery, 9(3), 114-120. https://doi.org/10.11648/j.sd.20210903.16

Copy | Download

ACS Style

Zhu Gan; Ding Jianguo. Simulation Study on Blast Resistance Test of Blast Wall Based on LS-DYNA Coupling Method. Sci. Discov. 2021, 9(3), 114-120. doi: 10.11648/j.sd.20210903.16

Copy | Download

AMA Style

Zhu Gan, Ding Jianguo. Simulation Study on Blast Resistance Test of Blast Wall Based on LS-DYNA Coupling Method. Sci Discov. 2021;9(3):114-120. doi: 10.11648/j.sd.20210903.16

Copy | Download

@article{10.11648/j.sd.20210903.16,
  author = {Zhu Gan and Ding Jianguo},
  title = {Simulation Study on Blast Resistance Test of Blast Wall Based on LS-DYNA Coupling Method},
  journal = {Science Discovery},
  volume = {9},
  number = {3},
  pages = {114-120},
  doi = {10.11648/j.sd.20210903.16},
  url = {https://doi.org/10.11648/j.sd.20210903.16},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.sd.20210903.16},
  abstract = {In order to study the pressure change with time at the blast face of the blast resistant wall when the shock wave acts on the blast resistant wall after the explosion of TNT explosive, the equivalent model of the blast resistant wall is designed based on the similarity theory, and the TNT near ground explosion test is carried out. During the test, the pressure change data of the design measuring point on the blast resistant wall with time are collected by high-speed data acquisition instrument and pressure sensor, The time history curve of shock wave overpressure was obtained by processing the data. Then, LS-DYNA finite element analysis software is used to establish a separate finite element model of the blast wall. At the same time, the relevant parameters of air, explosive, concrete and ground in the explosion field are set. The numerical simulation of the explosion field is carried out, and the overpressure time history curve at the measuring point is extracted by the finite element analysis post-processing software. Compared with the numerical simulation results, it is found that the numerical simulation results are in good agreement with the experimental data, which indicates that the selection and setting of parameters in the simulation calculation are reasonable. The model and algorithm provide an effective means for the numerical simulation of blast wall in the explosion field.},
 year = {2021}
}

Copy | Download

TY  - JOUR
T1  - Simulation Study on Blast Resistance Test of Blast Wall Based on LS-DYNA Coupling Method
AU  - Zhu Gan
AU  - Ding Jianguo
Y1  - 2021/05/24
PY  - 2021
N1  - https://doi.org/10.11648/j.sd.20210903.16
DO  - 10.11648/j.sd.20210903.16
T2  - Science Discovery
JF  - Science Discovery
JO  - Science Discovery
SP  - 114
EP  - 120
PB  - Science Publishing Group
SN  - 2331-0650
UR  - https://doi.org/10.11648/j.sd.20210903.16
AB  - In order to study the pressure change with time at the blast face of the blast resistant wall when the shock wave acts on the blast resistant wall after the explosion of TNT explosive, the equivalent model of the blast resistant wall is designed based on the similarity theory, and the TNT near ground explosion test is carried out. During the test, the pressure change data of the design measuring point on the blast resistant wall with time are collected by high-speed data acquisition instrument and pressure sensor, The time history curve of shock wave overpressure was obtained by processing the data. Then, LS-DYNA finite element analysis software is used to establish a separate finite element model of the blast wall. At the same time, the relevant parameters of air, explosive, concrete and ground in the explosion field are set. The numerical simulation of the explosion field is carried out, and the overpressure time history curve at the measuring point is extracted by the finite element analysis post-processing software. Compared with the numerical simulation results, it is found that the numerical simulation results are in good agreement with the experimental data, which indicates that the selection and setting of parameters in the simulation calculation are reasonable. The model and algorithm provide an effective means for the numerical simulation of blast wall in the explosion field.
VL  - 9
IS  - 3
ER  -

Copy | Download