Studying the Efficiency of the New Cotton Regenerator

Mirsolikh Agzamov; Akmalkhoja Khotamovich Inagamov; Mirkhosil Mirkhosil Mirsalikhovich Agzamov

doi:doi:10.11648/j.ajmme.20180204.11

| Peer-Reviewed

Studying the Efficiency of the New Cotton Regenerator

Mirsolikh Agzamov, Akmalkhoja Khotamovich Inagamov, Mirkhosil Mirkhosil Mirsalikhovich Agzamov

Published in American Journal of Mechanical and Materials Engineering (Volume 2, Issue 4)

Received: 19 November 2018 Accepted: 4 December 2018 Published: 3 January 2019

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

The article reflects the results of studies to determine the effectiveness of the created technological process from the waste of purifiers. The purpose of this work is to substantiate the improvement quality and output of fiber due to the modernization of the process regeneration of cotton slices from the waste products of cotton purifier machine. Improvement of the process of regeneration of the cotton slices from the waste of cotton purifiers by supplying the cotton slices to the regenerator, previously separated from the passive litter, with the development of a special device. In order to obtain the most complete characterization of such processes with a minimum number of experiments, experiments were carried out with extreme variants - with the supply of regenerated cotton slices to raw cotton before cleaning and ginning processes. Calculation based on weighted average clogging shows that if the number of regenerated cotton slices after the regenerator did not exceed 4% of the mass of raw cotton being cleaned, then their debris after triple cleaning by 1XK did not exceed 7.75%, which is almost 5 times higher than the debris of the cotton being cleaned raw. The most promising way of implementing the developed recommendation on the supply of sufficiently purified regenerated cotton slices into raw cotton before ginning is the development of a regenerator-purifier based on the 1РХ regenerator with built-in purifying sections from small litter.

Published in	American Journal of Mechanical and Materials Engineering (Volume 2, Issue 4)
DOI	10.11648/j.ajmme.20180204.11
Page(s)	33-39
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2019. Published by Science Publishing Group

Keywords

Cotton Purifier, Cotton Slices, Regenerator, Waste, Litter, Seeds, Free Fiber, Drum with Steel Rods

References

[1]	P. N. Borodin and etc., Improving the effectiveness of existing regenerators of raw cotton from waste (report), topic 9113, SID "Хлопкопром", Tashkent, 1992.
[2]	Industry guidelines "Primary processing of cotton, ginning medium-fiber varieties of raw cotton. A typical technological process." PPC 44-83, "ЦНИИХпром", pp 35, 1983.
[3]	Industry guidelines "Primary cotton processing. Fiber cleaning of medium-fiber cotton varieties. Typical technological process." PPC 45-83, Tashkent: "ЦНИИХпром", pp 17, 1983.
[4]	V. B. Tikhomirov, Planning and analysis of the experiment (when conducting research in the textile industry). M.: "Light industry", pp 253, 1974.
[5]	Yu. P. Adler and etc., Planning an experiment in the search for optimal conditions M.: "Science". pp 279, 1975.
[6]	V. V. Nalimov and etc., Planning of the experiment. - M.: "Science", pp 462, 1974.
[7]	E. F. Budin and etc., Exploratory Studies on the Creation of a Cleansing Complex Using Existing Equipment (report), topic 750901, Tashkent, 115 pp, 1975.
[8]	G. P. Nesterov, E. F. Budin, P. N. Borodin, Studies of the effect of the multiplicity and sequence of cleaning raw cotton in the spike and serrate sections on the technological indicators of raw cotton and fiber, Cotton Industry, #1, 1977.
[9]	Collection of instructions for process control and testing methods for raw cotton, fiber, lint, seeds and cotton waste of cotton plants. Tashkent: "Mexnat", pp 532, 1992.
[10]	Standard of the Republic of Uzbekistan PCT 581-91. Processing of raw cotton. Terms and Definitions. Tashkent: "УзНИИНТИ", 1991.
[11]	F. B. Omonov, Investigations of the effectiveness of a vertical fiber purifier during the purification process of a fiber of long-staple selections. Tashkent. J. Problems of textiles. #2, pp 15-19, 2010.
[12]	A. Kh. Inogamov, M. Agzamov, Improvement of the cotton batting regeneration technology in order to improve the fiber quality, “Progress 2008” Modern high technologies and promising materials for textile and light industry. Thesis of the report of the international conference - Ivanovo, pp 96, 2008.
[13]	M. M. Agzamov, S. Z. Yunusov, Z. K. Gafurov, The use of a new drying-purifying unit, international conference, Greece, Corfu, 2017.
[14]	M. Agzamov, S. Z. Yunusov, A. Kh. Inagamov, M. M. Agzamov, Synergy and integration, China, pp 205-211, 2018.
[15]	M. Agzamov, S. Z. Yunusov, M. M. Agzamov, Innovative working chamber for saw gin, Monograph, LAMBERT Academic Publishing, Latvia, p 42, 2018.

Cite This Article

Plain Text BibTeX RIS

APA Style

Mirsolikh Agzamov, Akmalkhoja Khotamovich Inagamov, Mirkhosil Mirkhosil Mirsalikhovich Agzamov. (2019). Studying the Efficiency of the New Cotton Regenerator. American Journal of Mechanical and Materials Engineering, 2(4), 33-39. https://doi.org/10.11648/j.ajmme.20180204.11

Copy | Download

ACS Style

Mirsolikh Agzamov; Akmalkhoja Khotamovich Inagamov; Mirkhosil Mirkhosil Mirsalikhovich Agzamov. Studying the Efficiency of the New Cotton Regenerator. Am. J. Mech. Mater. Eng. 2019, 2(4), 33-39. doi: 10.11648/j.ajmme.20180204.11

Copy | Download

AMA Style

Mirsolikh Agzamov, Akmalkhoja Khotamovich Inagamov, Mirkhosil Mirkhosil Mirsalikhovich Agzamov. Studying the Efficiency of the New Cotton Regenerator. Am J Mech Mater Eng. 2019;2(4):33-39. doi: 10.11648/j.ajmme.20180204.11

Copy | Download

@article{10.11648/j.ajmme.20180204.11,
  author = {Mirsolikh Agzamov and Akmalkhoja Khotamovich Inagamov and Mirkhosil Mirkhosil Mirsalikhovich Agzamov},
  title = {Studying the Efficiency of the New Cotton Regenerator},
  journal = {American Journal of Mechanical and Materials Engineering},
  volume = {2},
  number = {4},
  pages = {33-39},
  doi = {10.11648/j.ajmme.20180204.11},
  url = {https://doi.org/10.11648/j.ajmme.20180204.11},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajmme.20180204.11},
  abstract = {The article reflects the results of studies to determine the effectiveness of the created technological process from the waste of purifiers. The purpose of this work is to substantiate the improvement quality and output of fiber due to the modernization of the process regeneration of cotton slices from the waste products of cotton purifier machine. Improvement of the process of regeneration of the cotton slices from the waste of cotton purifiers by supplying the cotton slices to the regenerator, previously separated from the passive litter, with the development of a special device. In order to obtain the most complete characterization of such processes with a minimum number of experiments, experiments were carried out with extreme variants - with the supply of regenerated cotton slices to raw cotton before cleaning and ginning processes. Calculation based on weighted average clogging shows that if the number of regenerated cotton slices after the regenerator did not exceed 4% of the mass of raw cotton being cleaned, then their debris after triple cleaning by 1XK did not exceed 7.75%, which is almost 5 times higher than the debris of the cotton being cleaned raw. The most promising way of implementing the developed recommendation on the supply of sufficiently purified regenerated cotton slices into raw cotton before ginning is the development of a regenerator-purifier based on the 1РХ regenerator with built-in purifying sections from small litter.},
 year = {2019}
}

Copy | Download

TY  - JOUR
T1  - Studying the Efficiency of the New Cotton Regenerator
AU  - Mirsolikh Agzamov
AU  - Akmalkhoja Khotamovich Inagamov
AU  - Mirkhosil Mirkhosil Mirsalikhovich Agzamov
Y1  - 2019/01/03
PY  - 2019
N1  - https://doi.org/10.11648/j.ajmme.20180204.11
DO  - 10.11648/j.ajmme.20180204.11
T2  - American Journal of Mechanical and Materials Engineering
JF  - American Journal of Mechanical and Materials Engineering
JO  - American Journal of Mechanical and Materials Engineering
SP  - 33
EP  - 39
PB  - Science Publishing Group
SN  - 2639-9652
UR  - https://doi.org/10.11648/j.ajmme.20180204.11
AB  - The article reflects the results of studies to determine the effectiveness of the created technological process from the waste of purifiers. The purpose of this work is to substantiate the improvement quality and output of fiber due to the modernization of the process regeneration of cotton slices from the waste products of cotton purifier machine. Improvement of the process of regeneration of the cotton slices from the waste of cotton purifiers by supplying the cotton slices to the regenerator, previously separated from the passive litter, with the development of a special device. In order to obtain the most complete characterization of such processes with a minimum number of experiments, experiments were carried out with extreme variants - with the supply of regenerated cotton slices to raw cotton before cleaning and ginning processes. Calculation based on weighted average clogging shows that if the number of regenerated cotton slices after the regenerator did not exceed 4% of the mass of raw cotton being cleaned, then their debris after triple cleaning by 1XK did not exceed 7.75%, which is almost 5 times higher than the debris of the cotton being cleaned raw. The most promising way of implementing the developed recommendation on the supply of sufficiently purified regenerated cotton slices into raw cotton before ginning is the development of a regenerator-purifier based on the 1РХ regenerator with built-in purifying sections from small litter.
VL  - 2
IS  - 4
ER  -

Copy | Download

Author Information

Mirsolikh Agzamov

Department of Technological Machines and Equipment, Tashkent Institute of Textile and Light Industry, Tashkent, Republic of Uzbekistan
Akmalkhoja Khotamovich Inagamov

Department of Technological Machines and Equipment, Tashkent Institute of Textile and Light Industry, Tashkent, Republic of Uzbekistan
Mirkhosil Mirkhosil Mirsalikhovich Agzamov

Department of Technological Machines and Equipment, Tashkent Institute of Textile and Light Industry, Tashkent, Republic of Uzbekistan

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Mirsolikh Agzamov, Akmalkhoja Khotamovich Inagamov, Mirkhosil Mirkhosil Mirsalikhovich Agzamov. (2019). Studying the Efficiency of the New Cotton Regenerator. American Journal of Mechanical and Materials Engineering, 2(4), 33-39. https://doi.org/10.11648/j.ajmme.20180204.11

Copy | Download

ACS Style

Mirsolikh Agzamov; Akmalkhoja Khotamovich Inagamov; Mirkhosil Mirkhosil Mirsalikhovich Agzamov. Studying the Efficiency of the New Cotton Regenerator. Am. J. Mech. Mater. Eng. 2019, 2(4), 33-39. doi: 10.11648/j.ajmme.20180204.11

Copy | Download

AMA Style

Mirsolikh Agzamov, Akmalkhoja Khotamovich Inagamov, Mirkhosil Mirkhosil Mirsalikhovich Agzamov. Studying the Efficiency of the New Cotton Regenerator. Am J Mech Mater Eng. 2019;2(4):33-39. doi: 10.11648/j.ajmme.20180204.11

Copy | Download

@article{10.11648/j.ajmme.20180204.11,
  author = {Mirsolikh Agzamov and Akmalkhoja Khotamovich Inagamov and Mirkhosil Mirkhosil Mirsalikhovich Agzamov},
  title = {Studying the Efficiency of the New Cotton Regenerator},
  journal = {American Journal of Mechanical and Materials Engineering},
  volume = {2},
  number = {4},
  pages = {33-39},
  doi = {10.11648/j.ajmme.20180204.11},
  url = {https://doi.org/10.11648/j.ajmme.20180204.11},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajmme.20180204.11},
  abstract = {The article reflects the results of studies to determine the effectiveness of the created technological process from the waste of purifiers. The purpose of this work is to substantiate the improvement quality and output of fiber due to the modernization of the process regeneration of cotton slices from the waste products of cotton purifier machine. Improvement of the process of regeneration of the cotton slices from the waste of cotton purifiers by supplying the cotton slices to the regenerator, previously separated from the passive litter, with the development of a special device. In order to obtain the most complete characterization of such processes with a minimum number of experiments, experiments were carried out with extreme variants - with the supply of regenerated cotton slices to raw cotton before cleaning and ginning processes. Calculation based on weighted average clogging shows that if the number of regenerated cotton slices after the regenerator did not exceed 4% of the mass of raw cotton being cleaned, then their debris after triple cleaning by 1XK did not exceed 7.75%, which is almost 5 times higher than the debris of the cotton being cleaned raw. The most promising way of implementing the developed recommendation on the supply of sufficiently purified regenerated cotton slices into raw cotton before ginning is the development of a regenerator-purifier based on the 1РХ regenerator with built-in purifying sections from small litter.},
 year = {2019}
}

Copy | Download

TY  - JOUR
T1  - Studying the Efficiency of the New Cotton Regenerator
AU  - Mirsolikh Agzamov
AU  - Akmalkhoja Khotamovich Inagamov
AU  - Mirkhosil Mirkhosil Mirsalikhovich Agzamov
Y1  - 2019/01/03
PY  - 2019
N1  - https://doi.org/10.11648/j.ajmme.20180204.11
DO  - 10.11648/j.ajmme.20180204.11
T2  - American Journal of Mechanical and Materials Engineering
JF  - American Journal of Mechanical and Materials Engineering
JO  - American Journal of Mechanical and Materials Engineering
SP  - 33
EP  - 39
PB  - Science Publishing Group
SN  - 2639-9652
UR  - https://doi.org/10.11648/j.ajmme.20180204.11
AB  - The article reflects the results of studies to determine the effectiveness of the created technological process from the waste of purifiers. The purpose of this work is to substantiate the improvement quality and output of fiber due to the modernization of the process regeneration of cotton slices from the waste products of cotton purifier machine. Improvement of the process of regeneration of the cotton slices from the waste of cotton purifiers by supplying the cotton slices to the regenerator, previously separated from the passive litter, with the development of a special device. In order to obtain the most complete characterization of such processes with a minimum number of experiments, experiments were carried out with extreme variants - with the supply of regenerated cotton slices to raw cotton before cleaning and ginning processes. Calculation based on weighted average clogging shows that if the number of regenerated cotton slices after the regenerator did not exceed 4% of the mass of raw cotton being cleaned, then their debris after triple cleaning by 1XK did not exceed 7.75%, which is almost 5 times higher than the debris of the cotton being cleaned raw. The most promising way of implementing the developed recommendation on the supply of sufficiently purified regenerated cotton slices into raw cotton before ginning is the development of a regenerator-purifier based on the 1РХ regenerator with built-in purifying sections from small litter.
VL  - 2
IS  - 4
ER  -

Copy | Download